SMP - The two-chamber mixing pump!
When used in combination with the m-tec silo, the SMP silo mixing pump enables the rational processing of dry mortars. Product and machine as a system from one provider is made available to the processor as ready for operation on the construction site.
For a number of years, the SMP has been captivating with its powerful drive and blending of dry mortars. This is made possible by the m-tec own dual mixing system with two-way blending: two separated mixing zones guarantees a constant mortar consistency, independent of the degree of wear of the worm pump. The result: very good, homogeneous mortar quality even where the products are difficult to mix.
The SMP silo mixing pump is available in versions for processing plaster, refractory materials, flowing screed and adhesives. For small volumes the SMP can also be fed with bagged materials.
As is typical of all m-tec systems, the SMP has easy and quick to use tensioning wedges or swivelling devices that enable important elements, such as the worm pump, to be replaced in just a few seconds.
SMP - added benefits
Easy Work
Our intelligent machine technology allows you to work uninterrupted and without consistency changes. The separation of the dry and wet sections enables a constant ratio of dry material to water.
Easy Mix
Our patented mixing system enables an extremely good mixing quality. When used in conjunction with the two-way blending, the system guarantees the best-possible mix of mortar products.
Easy Use
The combination of clearly structured control elements, a foldable mixing zone, drive motors or tensioning wedges result in the simple handling of the SMP silo mixing pump.
Easy Life
The time-consuming and tedious adaptation of the processing machine are lost through the extremely high conveying value. Due to this you will have more time for your work.
SMP - facts
Areas of application and use
All pumpable dry mortar such as:
- Flowing screed
- Lime gypsum plaster
- Cement plaster
- Lime plaster
- Lime-cement plaster
- Masonry mortar
- Insulating plaster/render
- Finishing plaster
- Reinforcing and adhesive mortar
- Adhesive
- High-value products
Technical information
| SMP-P | SMP-FE | |
| Standard delivery volume: | approx. 30 - 100 l/min (dependent on version and worm pump) | |
| Conveying distance: | up to 120 m* | |
| Conveying height: | up to 30 m* | |
| Conveying pressure: | up to 30 bar* | |
| Mixing area: | 4.0 kW, 400 V, 50 Hz | 4.0 kW, 400 V, 50 Hz |
| Pump section: | 5.5 kW, 400 V, 50 Hz | 7.5 kW, 400 V, 50 Hz |
| Compressed air supply: | 0.9 kW, approx. 250 l/min, 4 bar | |
| Water pump: | 0.3 kW, approx. 40 l/min, 8 bar | 0.55 kW, approx. 60 l/min, 8 bar |
| Electrical connection: | 400 V, 50 Hz, 3 ph | |
| Fuse: | C 25 A | C 25 A |
| Connecting cable: | min. 5 x 4.0 mm² | |
| Connector: | 32 A, 5p, 6h | |
| Water supply: | 3/4" water hose with GEKA coupling (min. 2,5 bar while machine is running) | |
| Dimensions: | approx. 2200 x 800 x 1850 mm | approx. 2350 x 800 x 1900 mm |
| Required silo outlet height: | approx. 1300 mm | approx. 1400 mm |
*Dependent on consistency, quality and composition of the material, pump model and condition, diameter and length of the delivery hose as well as the pumping height of the material.
Recommended accessories
- Rotors/stators
- Mortar hoses
- Glue gun
- Finishing plaster spray gun
- Silo
- Silo placing unit
Scope of delivery
Silo mixing pump incl. compressor with automatic cut-off and water pump, rotor/stator, spray gun, set of hoses and accessories.
*Details differ depending on the product version and we shall not be held liable.
For further information, please contact your local sales representative.